Step by step guide
Go: replace inlet/outlet pipe
Servicing our pressure washers are quite straight forward and could be done by most people by following the step-by-step instructions in this manual. Please go trough the whole manual before starting work on your pressure washer to make sure you understand the procedure and that you have the necessary tools to complete the task.
Always unplug the pressure washer from both the mains power and the water outlet before starting the service. Even though power and water is disconnected there may be pressurized water in the hose. Discharge this pressure by pulling the trigger on the gun. Make sure your work area is clean and appropriate for the work you are about to do. There will usually be a small amount of water inside the pump and hose. If you are doing a 10-year service, then be prepared to collect the used oil from the oil chamber. Please dispose of the oil in accordance with local law and regulations. ISO 46 hydraulic oil can be substituted with similar non detergent oil of the same viscosity.
00. Parts and tools
An overview of what is needed to do this service.
01. Remove water filter
Unscrew the water filter then remove it.
02. Remove screws from the front cover
Release the pressure hose from the pump outlet. Unscrew the four T25 screws from the front cover.
03. Remove screws from the tool holder
Turn the pressure washer upside down. Unscrew the two T25 screws from the tool holder.
04. Open the machine
Remove the bottom of the tool holder cover, then remove the front cover.
05. Remove on/off knob
Remove the on/off button and the power cable strain reliever.
06. Remove screws from the switch box
Unscrew the two T25 screws from securing the switch box and motor/pump assembly.
07. Remove the motor/pump assembly
Carefully lift out the motor/pump assembly.
Remove the motor cowling from the motor/pump assembly. The removal of motor cowling is not strictly necessary for a 5-year service.
08. Remove u-pins
Remove the U-pin securing the inlet and/or outlet pipes from the pump head. Use a small flat head screwdriver to pry them loose.
09. Remove inlet and/or outlet pipe
Remove the inlet and/or outlet pipes from the pump head.
10. Attach the new inlet and/or outlet pipe
Reattach the inlet and/or outlet pipe. There is a small notch in the pump head that ensures correct alignment of the pipes.
11. Secure inlet and/or outlet pipes
Secure the inlet and/or outlet pipes with u-pins. You may want to use a small hammer or something similar to lightly tap them into the pump head.
12. Place the motor/pump back into the cabinet
Turn the motor/pump unit so that the switch box and water inlet is facing up and place it back into the rear cabinet.
13. Secure the motor/pump assembly
Secure the motor/pump and the switch box using the two T25 screws.
14. Attach the on/off knob
Put the on/off knob back on to the switch box.
Fit the power cable strain reliever into the slot.
15. Fit the front cover
Fit the front cover.
Check that the on/off knob can rotate freely.
16. Secure the front cover
Fix the front cover to the back cover by using four T25 screws as indicated.
17. Secure the bottom tool holder cover
Fit bottom tool holder cover and secure it with two screws.
18. Attach water filter
Check that the filter cassette is clean, then refit the water filter.
19. First start after service
Congratulations with finishing the service of your AVA product.
It is now time to do the first start after service.
- Start by connecting the pressure gun to the hose.
- Connect water.
- Make sure no water is leaking from the inside or anywhere else on the pressure washer.
- Pull the trigger and let the water flow until there is no more air coming out.
- Connect the power cord.
- Turn on the pressure washer.
- Pull the trigger and let water run for a minute before connecting a nozzle.
- Connect the nozzle. Use the pressure washer and make sure it is operating as normal.
20. Troubleshooting
Water is leaking from the inside
•Disconnect the power and open the pressure washer to locate the leak. Take necessary action to remedy any leaks.
Motor runs and won't stop when you release the trigger
•This is most likely due to an improper seating of the switch box on the start/stop valve. Open the machine and check that the switch box is correctly seated.
The pressure washer won't turn on
•Check that the power cable is connected.
•Check that the circuit breaker has not been tripped.
•Check that the fuse in the power plug is intact (UK models only).
•Open the machine and check that all the internal cabling is connected.
Poor performance/pressure
•Improper assembly or dirt/debris in the pump. Check that the pump and especially the main valve for foreign objects/debris. Make sure that the spring in the main valve is correctly seated and working as intended.